Latest Hardware Support topics

Topic	Replies	Views	Activity
Recovering servos on Mac with USB-C to USB-A converter? DYNAMIXEL-Protocol	2	148	April 18, 2023
Self tapping screw hole reusability X-Series	1	155	April 7, 2023
Type3 ping error for XM430 & open rb 150 Arduino , DYNAMIXEL-Protocol , OpenRB , X-Series	15	1134	April 4, 2023
3.3V and GND permanently shorted on opencr Shutdown , OpenCR	4	208	April 3, 2023
AX-12A and DYNAMIXEL Wizard2.0 OpenCM , DYNAMIXEL-Protocol , DYNAMIXEL-Wizard	6	628	March 17, 2023
6DOF OpenManipulator-X DYNAMIXEL-Protocol	1	125	March 16, 2023
Is the CM 700 product discontinued? CM-Series , AX-MX , DYNAMIXEL-Protocol	4	166	March 15, 2023
Inconsistent Reading of XL430-W250-T Motors on Rasberry Pi DYNAMIXEL-Protocol , U2D2 , RaspberryPi , X-Series	4	366	March 7, 2023
OpenMANIPULATOR-x control issue using OpenCR	15	1430	March 2, 2023
Type of wire used in X4P cable DYNAMIXEL-Protocol	3	241	February 28, 2023
Wizard2.0 unable to detect MX64 connected to OpenCM 9.04 + 468 Exp AX-MX , DYNAMIXEL-Protocol , OpenCM , U2D2	1	207	February 11, 2023
How tight should the horn be (XH540-W270R) 540 , DYNAMIXEL-Protocol , X-Series	1	200	February 8, 2023
Maximum velocity is being limited by PWM limit X-Series , Velocity-Mode , OpenRB	1	219	January 31, 2023
Problem with Dynamixel XL-320 using Arduino Uno rev 3 with Dynamixel Shield Arduino , DYNAMIXEL-Protocol , X-Series	5	546	January 19, 2023
AX-12A motor issues, Bioloid balance issues after installing new CM-530 controller AX-MX , DYNAMIXEL-Protocol	1	385	January 6, 2023
Running U2D2 + Dynamixel PH-Series with 26 VDC DYNAMIXEL-Protocol	1	179	January 6, 2023
XC 시리즈 서보의 3pin ttl 케이블을 임의로 1m 혹은 2m 정도로 연장해서 사용 가능할지 문의드립니다 Arduino , Position-Mode , X-Series , 한국어-Korean	1	239	December 29, 2022
Max 'pass-through' current in daisy-chain configuration Position-Mode , X-Series	2	433	December 16, 2022
XM540-W150 Reboots unexpectedly Shutdown , Position-Mode	1	153	December 15, 2022
motor moment of inertia Current-Mode	1	162	November 28, 2022
Current-based position controller Current-Mode , Position-Mode , Custom-Controller , X-Series	0	216	November 18, 2022
My computer does not recognize the motors AX-MX	1	260	November 18, 2022
OpenCM9.04 USART3 can not work with DYNAMIXEL TTL Bus simultaneously OpenCM , Arduino , DYNAMIXEL-Protocol	1	371	October 30, 2022
IMU sensor data Open CR 1.0 Position-Mode , Custom-Controller	1	324	October 17, 2022
XH-430-W210-R PWM frequency PWM-Mode , X-Series	1	249	September 13, 2022
Slamtec RPLidar A1 M8 with Waffle-pi TurtleBot3 , LIDAR	1	824	September 2, 2022
OpenCM compatibility Arduino , XL , OpenCM , OpenRB	2	315	August 31, 2022
SDA_1 and SLA_1 pins of OpenCM 9.04 Solved , OpenCM , Arduino	2	229	August 30, 2022
Restore factory settings XL430-W250-T DYNAMIXEL-Protocol , XL	5	269	August 30, 2022
OpenCM9.04 and XL-320 motors not working Arduino , XL , OpenCM , Solved	10	1914	August 27, 2022